...
MobileMap can also collect current GPS location at time of laser data capture and store it as an offset GPS coordinate point for later calculation of individual the target tree location. When using this functionality, it is recommended that a high quality, sub-meter GPS be connected to your MobileMap Android device to ensure that the tree location can be calculated accurately.
When a tree record is saved, if MobileMap finds offset coordinates, distance and azimuth and appropriate fields for storing tree coordinates, it will attempt to calculate and store the tree coordinates. If the Trees layer is a Point layer (rather than the typical non-spatial attribute table) it will also save the geometry for the record.
Some laser rangefinders (e.g., Haglof Vertex Laser Geo) can connect directly to a sub-meter GPS and calculate the target tree coordinates directly. When using these devices, MobileMap can receive and store the tree coordinates at the same time as the tree height information.
Note: maintaining the connection to a Bluetooth laser rangefinder prevents incremental backups of the database while in the Tree List. This means that if you have backups set to 20 trees, for example, and you collect the 21st tree on a plot, MobileMap will save the tree to the database, but will not run the scheduled incremental backup of the database. The backup will still run when the plot is closed, as MobileMap will close the Bluetooth connection at this time (and reopen it when the next plot is opened). If you are using a Bluetooth laser rangefinder and you are collecting a large number of trees per plot, you may want to close and reopen the tree list partway through the data collection to force MobileMap to make a database backup mid plot if you are concerned about not having frequent database backups.
Supported Devices
While most Bluetooth devices will pair with MobileMap android devices and communicate using the NMEA data specification, we have found that the exact messages sent vary by device manufacturer and model. The table below contains the laser rangefinders have been been integrated and tested to date. Similar devices by these manufacturers may work as well, but they have not yet been tested.
If you are a device manufacturer or vendor and would like to see your device listed here, please contact us. Similarly, if you are a MobileMap customer with a Bluetooth compatible device that is not listed here, we would like to hear from you to see if we can add support for your device.
Manufacturer | Model | Height | Distance | Azimuth | Offset X/Y* | Tree X/Y |
|---|---|---|---|---|---|---|
LaserTech (LTI) | TruPulse 200 | X | X | X | ||
LaserTech (LTI) | TruPulse 360R | X | X | X | X | |
Haglof | Vertex Laser Geo | X | X | X | X | X |
*Offset X/Y is captured from the MobileMap Android device via the onboard GPS antennae or a Bluetooth connected GPS (e.g., Juniper Geode or EOS Arrow 100). It does not come from the laser rangefinder itself, but the capture is triggered when laser rangefinder data are received, so the coordinates stored are the GPS coordinates at the time of laser data capture. It is essential that the GPS antenna be co-located with the laser rangefinder (not at plot center!) for these data to be useful.
...
Press ON button to turn laser on
Use DMS or SEND button to cycle through main options until you see SETTINGS, then press ON button to select
Use DMS or SEND button to highlight BLUETOOTH, then press ON button to select
Use DMS or SEND button to check the USE BLUETOOTH checkbox, then press ON button to return to main menu. The Bluetooth icon should be visible to indicate that Bluetooth is on.
...
Pairing to Android Device
...
Configure laser range finder tree-level settings found in Settings > MobileMap Cruise > Trees. Make sure to enter exact field names (not aliases) for all tree attribute fields that you intend to populate via the laser rangefinder. Available settings:
Setting | Purpose |
|---|---|
Tree Height 1 Field |
Used to store incoming height data, in units selected on the laser rangefinder. Typically used to record total tree height, but if 2 heights are collected for each tree (e.g., merch height and total height) this should be set to the lower height to enable collection of tree from bottom to top. | |
Tree Height 2 Field | Same as above, but if 2 heights are collected for each tree (e.g., merch height and total height) this should be set to the higher height to enable collection of tree from bottom to top. |
Tree Distance Field | Can be used to store incoming distance data, in units selected on the laser rangefinder. Typically used to record the distance of a tree from plot center or from a GPS measurement. |
Tree Azimuth Field | Can be used to store incoming azimuth data, in degrees. Typically used to record the azimuth of a tree from plot center or from a GPS measurement. |
Tree Longitude Field | Can be used to store the Latitude value for the target tree. Only possible when laser rangefinder includes an integrated or connected GPS and supports onboard calculation of target tree coordinates based on GPS location, distance and azimuth. |
Tree Latitude Field | Can be used to store the Latitude value for the target tree. Only possible when laser rangefinder includes an integrated or connected GPS and supports onboard calculation of target tree coordinates based on GPS location, distance and azimuth. |
Tree Offset Longitude Field | Can be used to store the Longitude value from the MobileMap device at time of laser rangefinder data capture. Typically used with Bluetooth sub-meter GPS connected directly to the MobileMap device. Used in post-processing to calculate the coordinates of the target tree. |
Tree Offset Latitude Field | Can be used to store the |
Latitude value from the MobileMap device at time of laser rangefinder data capture. Typically used with Bluetooth sub-meter GPS connected directly to the MobileMap device. Used in post-processing to calculate the coordinates of the target tree. |
Configure MobileMap’s Bluetooth connected devices
Actions > Bluetooth Devices
Find the correct Bluetooth device from the list of paired devices
Select the appropriate device type (Rangefinder LTI or Rangefinder Haglof)
Slide the toggle to enable this device
You should see a message saying that the device has been connected and a green checkbox by the device
Tap Save (disk icon) to close this dialog and save the settings
...
When using an TruPulse 200 and recording tree heights, use height Height (HT) mode.
Start by pointing at the tree and holding the ‘Fire’ button until the distance is displayed. Release the button.
Next, aim for the base of the tree and hold the ‘Fire’ button until the angle is displayed and steady. Release the button.
Next, aim for the desired height (e.g., merch height or tip of tree) and hold the ‘Fire’ button until the angle is displayed and steady. Release the ‘Fire’ button. The TruPulse will display the height in the viewfinder and send the result to MobileMap. Verify the value is correct and in the correct row and cell.
If the distance to tree is also desired, use the down arrow on the TruPulse 200 to select
...
Horizontal Distance (
...
HD) mode. Once in HD mode, start by pointing at the tree and holding the ‘Fire’ button until the distance is displayed. When you release the ‘Fire’ button, the TruPulse will display the horizontal distance to the tree in the viewfinder and send the result to MobileMap. Verify the value is correct and in the correct row and cell.
LaserTech TruPulse 360R
When using the TruPulse 360R the height, distance and azimuth can all be captured in height (HT) mode. When the first component (horizontal distance) is captured
Start by pointing at the tree and holding the ‘Fire’ button until the distance is displayed. When the ‘Fire’ button is released, it will be sent to MobileMap. An alert will sound and the distance and azimuth will be populated.
...
GPS offset coordinates will also be captured from the best available GPS location and displayed in the appropriate cells.
Next, then aim for the base of the tree and hold the ‘Fire’ button until the angle is displayed and steady. When the button is released, an alert will sound but no new data will be populated.
...
Haglof Vertex Laser Geo
...
Next, aim for the desired height (e.g., merch height or tip of tree) and hold the ‘Fire’ button until the angle is displayed and steady. When you release the ‘Fire’ button, the TruPulse will display the height in the viewfinder and send the result to MobileMap. Verify the value is correct and in the correct row and cell.
Haglof Vertex Laser Geo
When using the Haglof Vertex Laser Geo, collect data using 3-point height (HEIGHT 3P) mode. Use the DME and SEND buttons to cycle through the modes until HEIGHT 3P is displayed on the heads-up display.
Press the on button to select HEIGHT 3P mode and begin data collection
When the red dot sight is turned on (when viewing through viewfinder) and the display reads AIM AND PRESS ON TO FIRE LASER, aim at an optional point on the target tree and give a short press at ON to measure the distance and angle to the tree. Continue to aim at that point on the tree until a short beep goes off and a result is shown in the heads-up display.
A temporary height result, to the point you are aiming at from ground, including the preset eye
height, is shown, but this should be ignored.If you have missed the target, you can start over by aiming at the point, and give a quick/short press at ON.
If needed, use the DME button to temporarily change the preset Laser mode (First-, Strongest-, Last- target) to allow the laser to work in optimal mode for the current measuring situation. For example, use Last-target to avoid having the laser reflect on objects in front of your target object, such as grass or bushes.
Aim at the base of the tree. Press ON and keep pressing until a beep goes off and the aiming dot is turned off. Release the ON button.
Aim at the top (or other height) on the tree. Press ON and and keep pressing ON until a beep goes off and a result is shown in the heads-up display. Release the ON button.
The heads-up display will now show the results including:
SD Slope Distance (m or feet)
HD Horizontal Distance (m or feet) - This can be stored in MobileMap when a distance and offset is needed for stem mapping. It can also be used in conjunction with the limiting distance tool in MobileMap to determine if a borderline tree is in.
DEG Angle (Degrees, % or Gradians) - This can be stored in MobileMap when a distance and offset is needed for stem mapping.
H1 Height (m or feet) - This is the most commonly used data from laser rangefinders and can be total height or merch height, depending on the cruise spec.
Press the Send button to send all measurements to MobileMap. You should hear the alert and see all fields (height, distance, azimuth, offset latitude, offset longitude) populate with the collected values. During initial testing, we recommend that these numbers are compared to the values displayed on the Haglof heads-up display to ensure that the measurements have been mapped to the correct fields in the tree list.
Troubleshooting
As described above, if you open the tree list and you do not see the cyan highlights for attribute fields that will be populated by the laser range finder then either a) the fields settings have not been properly configured in Settings > MobileMap Cruise > Trees, or b) the laser range finder has not been properly paired, configured or is not on.
...